Villamosmérnöki munka Jobs

I would like to carry out modeling and simulation using MATLAB/Simulink for a system that includes: Implementation of an MPPT strategy for a doubly-fed synchronous wind generator using Backstepping control; Design and implementation of an intelligent MPPT control for the photovoltaic system; Modeling of an energy storage system associated with a resistive load; Connection to the grid and addition of a resistive load; Development of an intelligent system based on a neural network for supervision, energy management, and fault diagnosis. The work will be presented in the form of a report written in Microsoft Word, describing in detail the algorithms used, the analysis of the simulation results, and their interpretation. The final part, dedicated to the intelligent supervision, energy m...

I need a well-structured Excel workbook that walks me through selecting every major component for a standard EOT crane. After I type in fundamentals—capacity, span, duty class, lift height, ambient factors—the sheet should calculate and recommend suitable options for three areas: the hoist system, the bridge & runway, and all key electrical components. Formulas must be laid out transparently in a way that lets me trace or adjust them later, with a separate tab summarising assumptions, safety factors and any reference tables you draw from IS, FEM or comparable crane design standards. Because I’m open to any brand that meets the spec, keep the logic brand-neutral yet show the exact parameters I’ll need to compare catalogues (motor kW, gearbox ratios, rail sizes,...

I need an embedded engineer to help safely connect a PCB to a lead-acid battery pack in series and integrate 4 external sensors (temperature, humidity, water presence, etc.). The system must read data in Arduino IDE and, if possible, send it to an existing telemetry endpoint (HTTP/MQTT). Scope: Safe wiring from battery pack to PCB Best way to connect and mount sensors Connector and grounding recommendations Simple Arduino example to read sensors and output/send data Experience with ESP32, Arduino, sensors, and battery-powered systems required.

Need getting Ionic Fingerprint from Saliva Need the schematic design circuit for this, with its components

I am finalising patent applications for a family of electrical neuro-stimulation medical devices and need all formal drawings produced to filing standard. Your portfolio must already show similar electrical patent work because accuracy and regulatory compliance are critical. Scope • Produce complete figure sets for each device, covering the required top, bottom, side and cross-sectional views. • Drawings must meet every line-weight, margin, font and reference-number rule in both UKIPO and USPTO manuals of patent drawing practice. • Clean, black-and-white line art only; no colour or gradients unless expressly allowed. Deliverables 1. Ready-to-file PDF sheets for UK and US filings. 2. Native vector files (e.g., AI or DWG) so I can make small future edits. 3. ...

1) Project goal Design a single PCB device for testing cable harnesses up to 25 wires, where both ends of the same harness are connected to the board: Side A: 25 lines (A1..A25) Side B: 25 lines (B1..B25) Total: 50 signal lines on the PCB. The detailed test logic (continuity/shorts/mapping) will be implemented in firmware later. For this phase, the key deliverable is robust hardware (schematic + PCB) prepared for such testing. 2) Scope of work (hardware only) Electrical schematic PCB layout Production files: Gerbers + drill BOM (with specs and acceptable alternatives) Assembly files (pick&place/positions) preferred Short mapping table: MCP23017 pins → A/B line numbers (Firmware is NOT required in this phase. Optional “I2C scan / basic blink” is a bonus.) 3...

My heating installation is already wired with motorised valves and PT-100 temperature sensors; what it still needs is a clean, reliable control program running on a Schneider Electric PLC. All field devices will communicate over Modbus TCP/IP, so the job centres on writing and testing the logic that opens or closes each valve, reads every sensor, and enforces the temperature set-points and safety limits I will provide. You’ll work directly in EcoStruxure Control Expert (Unity Pro), mapping the correct holding/input registers, building the sequence logic (ladder or structured text—your choice), and setting up alarms and manual-override modes. Once the code is ready, I’ll load it on site; remote commissioning support through VPN is essential to fine-tune timing and confirm...

I am midway through an online electrical training program and still have two graded components left in each module: the “learning activity” and the “content quiz.” Both are multiple-choice, can be retaken without limit, and I need a final score of 90 % or higher on every attempt that counts toward my record. You will receive screen-shots of every unfinished unit plus login access so you can work directly in the platform. Feel free to lean on AI tools or any personal reference material; the school places no restriction on outside resources. When you reply, please mention any hands-on electrical background, coursework, or certifications that show you can navigate these topics confidently. Deliverables • All remaining learning activities submitted with ≥...

I would like the IEEE 33-bus distribution feeder recreated in RSCAD v6 so that it runs smoothly in real time on my single-rack RTDS. The base network must be stable, clearly documented inside the workspace, and organised under three separate simulation cases: 1. Baseline (no DER, no EV) 2. PV + BESS + EVCS with V2G enabled 3. EVCS with V2G only I’ll provide the complete MATLAB data set that defines the component ratings, daily profiles, dispatch assumptions and any controller logic already worked out offline. Your task is to translate all of that into RSCAD, verify compile/run success at a 50 µs timestep, and deliver a balanced model that can be opened and executed immediately on the RTDS without further edits. Please let me know: • Your earliest start date and est...

I’m looking for an experienced aftermarket specialist to help me squeeze more performance out of my sports car. The priority is performance upgrades, starting with an aggressive body-kit package and any complementary tweaks that will genuinely improve aerodynamics, handling, and acceleration without compromising reliability. Here’s what I have in mind: • Custom-fit body kit installation and precise alignment • Suggestions on any additional performance parts that pair well with the kit (intake, exhaust, ECU remap, suspension fine-tune, or upgraded brakes if they add measurable gains) I’ll provide the car, workspace access, and all agreed-upon parts in advance. Your role is to advise on the optimal kit, confirm compatibility, carry out the install, and road-te...

I have been subjected to to “voice-to-skull” transmission, direct energy weapon and remote neural monitoring(remotely). My main concern right now is the physical discomfort it is causing—persistent headaches, muscle pain, fatigue, blurred vision,disorder sleep and many other things. I need help to stop it. You must have knowledge about RF wave, WIFI wave. Here is what I expect from you: • A brief consultation (voice or message) where you help me describe my symptoms and living environment in enough detail for an accurate assessment. • A written action plan that includes: – Practical counter-measures I can put in place immediately (shielding materials, RF detection equipment, grounding techniques, etc.). – Any recommended tools or devi...

I'm looking to develop a mechanical device with 4 adjustable roads coming in and going out from the center diagonally. The roads should have adjustable lengths, and the adjustments will be done manually. Ideal skills and experience: - Mechanical engineering - Proficiency in designing adjustable structures - Experience with manual adjustment mechanisms - Strong problem-solving skills Please provide examples of similar work done.

I'm seeking a creative professional to design a unique and effective Heron scarer that operates from inside a property, similar to a room air freshener. Key Features: - Power: Both battery and mains-powered options - Activation: Scheduled timer - Alert Mechanism: Device motion, with optional flashing lights Ideal Skills and Experience: - Experience in product design - Knowledge of electronic mechanisms - Creativity in developing unique solutions - Ability to integrate timers and motion alerts Please provide a portfolio showcasing relevant work.

I’m looking for an experienced electronics designer to develop a complete industrial-grade control system consisting of two devices: 1. Transmitter (TX) – collects inputs from joysticks and other signals (8 analog + 2 digital + AUX). 2. Receiver (RX) – receives data from TX via CAN and drives power outputs. Communication between TX and RX must be via CAN bus. The system must operate on 12V or 24V vehicle/machine installations, with a supply range of 9–27V DC. Scope includes schematic design, SMD PCB design, and enclosure selection/design. ⸻ Functional Requirements TX (Transmitter) • 8 analog input channels (joysticks / analog signals) • 2 digital inputs • 1 AUX signal (logic/auxiliary) • Analog measurement must use an industrial-grade ...

I need a complete electrical CAD drawing that shows a detailed layout of the building’s wiring system. The goal is to have representation of CCTV, Access, electrical, mux etc as per As-built drawing standards. You’ll be working from my existing floor layout PDF Using AutoCAD (or a fully compatible platform), translate this information into a clean, well-annotated DWG that includes all conduit routes, cable types, breaker sizing, legends, and schedules. Please follow standard electrical drafting conventions so the file integrates smoothly with other trade drawings. Deliverables • A native .dwg file with organized layers for lighting, power, low-voltage, and notes • A plotted PDF for quick review at 1:100 • Any custom blocks or symbols you create, saved se...

I want to commission the full design package for a 3 kW CNC laser cutter with a 1.5 × 3 m worktable. The machine will spend most of its life slicing stainless-steel sheet, so every component—from the fiber-laser source to the motion system—has to stand up to continuous metal duty while holding a repeatable ±0.1 mm tolerance. Here is what I expect to receive: • Detailed mechanical drawings for the bed, gantry, enclosure, fume extraction and assist-gas lines • Electrical schematics covering mains distribution, laser power supply, servo/stepper drives, control cabinet layout and all safety interlocks (E-stop, door sensors, light curtains) • A complete bill of materials with manufacturer part numbers, lead-times and estimated costs • Recomme...

Seeking experienced hardware engineer to build a prototype of a wall-mounted emergency device. Specs: Form Factor: Wall-mounted, compact, durable enclosure (weatherproof if outdoor use intended). Primary Function: Transmit pre-programmed GPS coordinates to a central monitoring location (e.g., server, app, or emergency service) upon activation for real-time tracking. Transmission Methods: Primary: GSM (cellular network) for cost-effective, low-latency sending. Failover: Satellite (e.g., Iridium or Globalstar network) if GSM unavailable. Power Source: Battery-powered with optional mini solar panel for recharging. Standby Battery Life: Minimum 1 year without charging (low-power mode). User Interface: Single button for activation; 2 LEDs for status feedback. Key Features Programming: Devic...

My 4.5 V circuit needs a small solar panel and the proper charge-management hardware so daylight tops the battery up automatically. I’m not sure what panel voltage or wattage is best, nor which controller IC will keep the Li-ion safe—so I need your electronics expertise. Scope of work – I'll share my schematic of the existing 4.5v circuit – Select or design a charge-controller stage that handles lithium-ion chemistry, prevents over-charge/over-discharge, and outputs a stable 4.5 V rail to the load. – Provide a clear schematic, concise BOM with part numbers that are easy to source, and wiring instructions I can follow on perfboard or a small PCB. – Advise on any protection components (diodes, fuses, reverse-polarity safeguards) so the device...

I am looking for an experienced CST Microwave Studio expert to help optimize and correct my CST design so that its S-parameter results closely match my HFSS simulation. I have already designed a bandpass filter operating from 8 GHz to 16 GHz in HFSS, and the results are correct. I replicated the same design in CST, but due to port configuration / port definition issues, the CST results are not matching the HFSS response. Your task is NOT to redesign the filter, but to: Analyze my existing CST model Identify issues related to ports / excitation / boundary setup Optimize the CST port settings and simulation setup Adjust the CST model (only where necessary) Ensure CST S-parameters closely match HFSS results What I Will Provide: HFSS design file HFSS S-parameter results PowerPoint with full ...

I'm seeking a skilled kitchen remodeler to modernize my kitchen. The design should be contemporary, incorporating the following elements: - Smart appliances - Granite or quartz countertops - Under-cabinet lighting Ideal skills and experience: - Expertise in contemporary kitchen designs - Experience with smart home technology integration - Proficiency in installing granite or quartz countertops - Knowledge of under-cabinet lighting systems Please provide a portfolio of similar work and an estimated timeline.

Project Description: I am looking for an experienced RF/Antenna Design freelancer to design and simulate a flexible wearable antenna using ANSYS HFSS for my final year project. Scope of Work: Design of a flexible microstrip/patch antenna for 5G (Sub-6 GHz, e.g., 3.3–3.8 GHz) and/or IoT band Selection and modeling of appropriate flexible substrate material (e.g., Polyimide, Rogers RT/duroid, textile substrate) Optimization of antenna parameters (length, width, feed position, ground structure, etc.) Simulation and analysis of key parameters: S11 (Return Loss ≤ -10 dB) VSWR Gain and Directivity Radiation Pattern (2D & 3D) Bandwidth Radiation Efficiency Bending analysis to evaluate performance under curvature (wearable condition) Parametric study and comparison with provided refe...

I need a clean, well-commented Arduino sketch for the Pololu 3pi that lets the robot visit six preset locations, interact with the magnet at each spot, and return to its starting line in under four minutes. The only sensing method available is a magnetic sensor array, so all point detection and interaction logic must rely on that hardware. Two run modes have to coexist in the same program and be switchable through a simple flag, jumper, or serial command: • Intermediate – the robot must physically touch the magnet before leaving the point. • Difficult – the robot should recognise the magnetic field, stop just short of contact, and then continue. Between locations, I expect a mix of straight dashes and graceful curves; please handle path planning so the 3pi&r...

Looking for Sound Engineer – Live Voice Transmission Optimization (Hardware + Embedded) I am currently looking for an experienced Sound Engineer / Audio Systems Engineer who is capable of working on live voice transmission from a tablet to standalone hardware such as Raspberry Pi / ESP32-based systems. * The product is already built and functional * The requirement is mainly for optimization, testing, and technical feedback * Focus areas include: audio transmission stability reduction quality optimization –software integration feedback 5.Real-world performance testing This is a great opportunity if you have experience with: * Embedded audio systems * Live streaming audio pipelines * IoT audio hardware * Signal processing for voice transmission If you have worked on similar ...

PROJECT OVERVIEW We are seeking an experienced Power Electronics / Control Systems Engineer to support a STATCOM upgrade project Upgrade from old controller PSR II ABB uses the ABB AC800PEC . The objective is to design, implement, and deploy control algorithms developed in Simulink / MATLAB into the AC800PEC Toolbox environment, ensuring real-time execution and stable grid performance. ________________________________________ SCOPE OF WORK The selected engineer will: 1 Control Algorithm Development • Develop and/or refine dq-axis current control • Design PLL (Phase-Locked Loop) for grid synchronization • Implement DC link voltage control • Reactive power / voltage regulation control • PWM generation strategy 2 Model-Based Design • Develop control models in Sim...

I need an experienced electronics / PCB engineer to design a reliable 24/7 traffic light controller PCB. This is a safety-critical industrial system, not a hobby project. System Details: 220VAC traffic light LED modules Control via TRIAC (optocoupler + TRIAC driver) Continuous 24/7 operation ESP32-based control Fail-safe design required Industrial-grade AC mains design Using EasyEDA Requirements: Strong ESP32 hardware experience Experience with AC mains / TRIAC design Experience with industrial / high-reliability systems Comfortable designing fail-safe protection systems Timeline (strict): Day 1: Complete schematic Day 2: PCB placement & routing If it takes longer, it means you are not experienced enough — this is not a complicated project. You must be ready to...

I have five separate street-lighting circuits, each running roughly 1 km and powered by LED fixtures. For every run I must keep the voltage drop under 3 % . Your job is to size the conductors, select protective devices if required, and supply clear voltage-drop calculations that prove compliance for each feeder. Please base the work on standard RTA specs, and assume a three-phase, four-wire low-voltage supply 400V. Deliverables • Single-line or schematic for all five circuits showing conductor sizes and protection • Spreadsheet or calculation sheet detailing input data, formulas, and the final % drop for every circuit • Short narrative explaining any assumptions, cable grouping or ambient-temperature corrections applied I will review the numbers, confirm that no...

We need an engineer experienced with MZ Automation openIEC61850 to build a complete IEC 61850 Edition 2.1–compliant SCL package for our Smart Grid controller (Linux-based OEM device acting as an IEC 61850 Server via LAN). Deliverables SCL files: ICD / CID / SSD / SCD (as applicable) Conformance paperwork: PICS / PIXIT / TICS / MICS Automation (preferred): scripts/tools to generate plant-specific SCL from our plant configuration file for future installations Key Requirements All Logical Nodes / DOs are defined in our internal spec — implement exactly what’s listed (no guessing) Logical Node naming must comply with CEI 0-16 (Annex T) Data transmission: some values every 4s, some on change, some on request, plus controls/setpoints from client We want an optimized dataset/r...

I need the 2026 GC front panel converted into a production-ready Gerber package so my board house can mill an exact aluminum faceplate. All mechanical data are already prepared: you’ll receive a clear photo of the current panel plus an Excel sheet detailing every cut-out, hole diameter, and positional coordinate. No circuitry is involved—this is purely a mechanical PCB. Here’s what I expect: • A clean RS-274X Gerber set, including drill file, that matches the spreadsheet dimensions to the tenth of a millimetre. • A simple PDF drawing or fabrication note that calls out all critical sizes for one last visual check before I release it to the shop. Please stick to the manufacturer’s standard rules; I’ll share their design-rule file once we start, ...

Kérjük, regisztráljon vagy jelentkezzen be a részletek megtekintéséhez!

I need an experienced contractor to build an in-ground swimming pool. The project includes: - Installing PVC pipes for plumbing - Setting up LED lights for illumination - Creating a machine room for pool equipment Ideal skills and experience: - Background in pool construction - Familiarity with PVC piping and electrical work for LED lights - Ability to design and build a functional machine room Please provide a portfolio of similar work.

I need a medium complexity (3-4 layers) PCB designed for signal processing. The design should be capable of accommodating surface-mount components. Requirements: - 3-4 layers PCB design - Signal processing functionality - Surface-mount component integration - Gerber file generation Ideal Skills: - Experience with PCB design software (e.g., Altium, Eagle) - Strong understanding of signal processing circuits - Proficiency in layout for surface-mount components - Attention to detail and accuracy Please provide samples of previous work.

I need an engineer who already works comfortably with the MZ Automation (openIEC61850) library to build a complete, Edition 2.1–compliant SCL file for one of our Smart Grid systems. All logical nodes to be modelled are spelled out in my internal specification document, so you will not have to guess any class names or data objects; just implement exactly what is listed. I need SCL files and tools (preferably automatic or semi-automatic) to generate the required files (ICD, CID, SSD, SCD) starting from our plant configuration file for each specific installation in the future. Alongside the SCL you will prepare the full set of IEC 61850 conformance paperwork: • PICS • PIXIT • TICS • MICS

Necesito apoyo puntual para completar varios cuestionarios tipo test de mi módulo de Electromecánica de Coches. Los ejercicios abarcan todos los bloques habituales del temario: sistemas de encendido, transmisiones automáticas, frenos y seguridad, además de los fundamentos eléctricos y mecánicos que conectan cada sistema. Trabajo con fechas de entrega cercanas, por lo que valoro respuestas claras y justificadas ‒una breve explicación detrás de cada opción elegida me ayuda a afianzar el contenido antes del examen. Entrego cada test en PDF o fotos; basta con que me devuelvas el documento resuelto y, cuando sea posible, una nota rápida sobre el razonamiento. Busco a alguien que domine la materia práctica, esté...

I'm looking for a device that can measure weight in pounds and operate underwater. It's essential that this device is powered by long-lasting batteries. Key Requirements: - The device must be waterproof and able to function accurately while submerged. - It should measure weight specifically in pounds. - Long-lasting battery life is crucial to ensure extended use without frequent recharging or replacement. Ideal Skills and Experience: - Experience in designing waterproof electronic devices. - Knowledge in weight measurement technology. - Expertise in battery technology for prolonged usage. Please provide examples of previous work and relevant experience in your bids.

I’d like the design published here turned into a finished, fully-working machine and delivered to me ready for use. The printable parts in the download need to be produced on a reliable FDM printer, finished cleanly, and paired with the necessary electronics. Key tasks you’ll handle • 3D-print every part from the MakerWorld files in a strong, heat-resistant material. Some parts need to be printer in PETG. • Source and install the electronics including arduino, wire everything neatly. • Run a full test roll, capture a short video showing the winder in action. • Ship the completed unit. Needs to work for Australian plug 240V. Total parts cost is estimated at US$170 ## Estimated Parts Cost **Electronics:** - Arduino Nano: ~$5–8 - DC Motor 1...

I need a technical engineering document currently written in English rendered into clear, precise Spanish without losing any of the specialised terminology or formatting. The file contains formulas, figures and a few embedded tables, so consistency in unit notation and layout is important to me. You will work directly from the source file and return a Spanish version that mirrors the original structure, plus any notes where terminology may be ambiguous. If you like to rely on CAT tools such as Trados, MemoQ or Wordfast, feel free—I welcome anything that helps maintain term consistency and speeds up delivery. Engineering background or proven experience with manuals, datasheets or specifications is a must, as the text includes references to mechanical tolerances and material standar...

I have a finished KiCad PCB layout and now need a clean, print-ready PDF compiled from it. The final document must contain six A4 landscape pages arranged in this exact order: 1. Copper Top Layer 2. Copper Inner Layer 1 3. Copper Inner Layer 2 4. Copper Bottom Layer 5. Component Placement Top Layer 6. Component Placement Bottom Layer Resolution has to be crisp enough for both close-up review and high-quality printing. I’ll provide the KiCad source files as soon as we get started; you simply export each required layer, keep KiCad’s default rendering colours, and merge them into a single PDF. I’ve attached a previous example—please note the labels are mirrored on that file due to an earlier issue, so yours should read correctly. Deliverable • O...

Hello, I am looking for an experienced PCB designer to complete schematic review and PCB layout for an ESP32-based industrial IoT board using EasyEDA (Collaborator mode). Scope of Work 1. PCB Outline & Mechanical Alignment The PCB outline must match an existing device layout based on measurements and connector positions that I will provide. There is no reference Gerber file, so the board outline must be recreated carefully and confirmed with me before routing. 2. Schematic Review & Improvement (Important) You must review the schematic and confirm it is electrically correct and suitable for stable operation, including: Component ratings verification Power design validation Decoupling and grounding ESP32 stability considerations LM2596 switching regulator layout considerations Identi...

I need an experienced draftsman to create detailed electrical drawings for a commercial building project using AutoCAD. The scope includes: - Power distribution plans - Network cabling layouts - CCTV system designs Ideal skills and experience: - Proficiency in AutoCAD - Expertise in electrical drafting for commercial buildings - Knowledge of power distribution, network cabling, and CCTV systems - Attention to detail and accuracy Please provide samples of previous work and a timeline for completion.

I'm seeking an experienced PCB designer to create a double-layer PCB for a consumer electronics radio project. The PCB will include microcontrollers as key components. Key Requirements: - Design a double-layer PCB - Incorporate microcontrollers into the design - Suitable for consumer electronics use Ideal Skills and Experience: - Proficiency in PCB design software (e.g., Altium, KiCad) - Experience with double-layer PCB design - Knowledge of microcontroller integration - Background in consumer electronics Please provide samples of previous work and relevant experience.

I need an expert to tune a DSP (Digital Signal Processor) for a custom-built Bluetooth speaker aimed at delivering a balanced sound profile across all music genres. The speaker will be used primarily for music. Requirements: - Use of Sigma Studio for DSP tuning - Tailoring sound profile to specific speaker and box size - Experience with balanced sound profiles - Knowledge of various music genres The ideal candidate should have a strong background in audio engineering and experience with DSP software.

I need an existing wiring schematic revised to add one component. Requirements: - Current schematic is scanned from PDF - Need to add a green pilot light Ideal Skills: - Experience with wiring schematics - Proficient with PDF editing and schematic modification - Attention to detail and accuracy

I already have a complete running PLC program developed in Siemens TIA Portal V20 for: PLC: Siemens S7-1200 (CPU 1212C) HMI: Siemens HMI (compatible with TIA Portal V20 project) The machine is already operational. I now need specific modifications and corrections in the existing logic. Scope of Work 1 Open and fully review the existing PLC and HMI project. check the list of required changes that I have mentioned inside the project files. the required logic changes properly. there are no conflicts with existing blocks, functions, or interlocks. that all modes (Auto / Manual / Safety logic) behave correctly after modification. the updated project file with clean structure and comments where required. 7. Install the program remotely on PLC and HMI Important – Read Before Qu...

I need the attached meter-layout sketch converted into a clean, professional one-line diagram showing the runs from the utility transformer to the meter pan. Label and conductor size must match the attached layout. Should include title block and sheet Deliverables: • PDF suitable for submission I’ll review the PDF against the template to make sure it's as requested; once it matches both, the project is complete.

I need a focused research effort that looks at satellite-communication antennas from three angles at once: maximising signal strength and quality, mapping frequency-band usage, and refining antenna design and materials. The outcome should give me clear, data-backed guidance I can hand straight to my hardware team. Scope You will survey current literature and patents, run electromagnetic simulations (HFSS, CST, FEKO or similar), and translate the findings into practical design recommendations. Emphasis is on L-, S- or Ku-band performance; however, if your analysis uncovers a better-suited band, flag it and justify the choice. Deliverables • Concise comparative report (PDF) • Simulation files with setup notes • Performance charts showing gain, VSWR, efficiency and li...

Saya masih berstatus pelajar dan belum memiliki pengalaman kerja, tetapi saya ingin mulai menapaki dunia profesional di bidang kelistrikan. Saya membutuhkan pendampingan ringan untuk: • Menyusun CV serta profil online sederhana yang menonjolkan minat dan kompetensi dasar saya di kelistrikan. • Membimbing saya memahami cara mendaftar pekerjaan paruh waktu, magang, atau proyek freelance yang relevan. • Memberi daftar sumber lowongan tepercaya dan kiat singkat menghadapi proses rekrutmen awal. Fokusnya adalah panduan praktis yang mudah saya ikuti selagi tetap menyesuaikan dengan jadwal sekolah. Jika Anda berpengalaman di industri listrik atau pernah membantu pemula memasuki pasar kerja, bantu saya memulai langkah pertama ini.

I’m kicking off a multi-phase R&D effort devoted to the design and development of cutting-edge microstrip antennas. The overarching targets are straightforward: boost usable bandwidth while simultaneously lifting signal strength, all without compromising the core advantages of printed technology. Phase by phase, I’ll be iterating from theoretical models through to lab-verified prototypes. You’ll take the lead on concept generation, electromagnetic simulation (HFSS, CST or an equivalent full-wave solver), layout refinement, and hand-over for fabrication. Once hardware comes back, we’ll compare measured S-parameters and radiation patterns against the simulated baseline, fine-tune, and document lessons learned for the next spin. Key deliverables • Simulation...

Projeto: Engenharia Reversa de Placa Eletrônica Legada Descrição do Projeto Busco profissional com experiência comprovada em eletrônica para realizar engenharia reversa completa de uma placa eletrônica legada, com o objetivo de: Reproduzir fielmente o funcionamento elétrico original Modernizar componentes obsoletos Gerar documentação técnica completa e atualizada Garantir compatibilidade mecânica, elétrica e funcional com o equipamento original O projeto seguirá um procedimento técnico estruturado já definido internamente Escopo do Trabalho O profissional deverá executar as seguintes etapas: 1. Análise e Correlação do Esquemático Verificaç&...

I need a comprehensive specification package for a generator set that will serve as an emergency backup at an industrial site. The unit must deliver more than 50 kW and be sized, selected, and laid out so that it can start automatically when grid power fails and keep critical plant loads online until utility service is restored. What I am looking for: • Load assessment and sizing calculations that justify the recommended kVA/kW rating (above 50 kW). • A shortlist of commercially available diesel or gas gensets that meet those requirements, including model numbers, fuel consumption tables, and compliance with local emission standards. • A single-line diagram showing the genset, automatic transfer switch (ATS), and main distribution connections. • An installation l...

_Project Title:_ Nickel Mine and Solar Power Plant (PLTS) Development _Objectives:_ - Increase nickel production to meet global demand - Develop renewable energy by building a 100 MW Solar Power Plant (PLTS) - Boost national revenue through nickel and electricity exports _Targets:_ - Nickel production: 100,000 tons/year - PLTS capacity: 100 MW - Target markets: Steel industry, battery manufacturers, and electricity sector _Steps:_ 1. _Exploration and Evaluation_: Conduct geological surveys and assess nickel reserves (6 months, Rp10 billion) 2. _Infrastructure Development_: Build roads, processing facilities, and power grid connections (12 months, Rp50 billion) 3. _PLTS Construction_: Build a 100 MW Solar Power Plant (18 months, Rp150 billion) 4. _Production Operations_: Start nickel and...