Nyomtatott áramkör Jobs

I need an embedded engineer to help safely connect a PCB to a lead-acid battery pack in series and integrate 4 external sensors (temperature, humidity, water presence, etc.). The system must read data in Arduino IDE and, if possible, send it to an existing telemetry endpoint (HTTP/MQTT). Scope: Safe wiring from battery pack to PCB Best way to connect and mount sensors Connector and grounding recommendations Simple Arduino example to read sensors and output/send data Experience with ESP32, Arduino, sensors, and battery-powered systems required.

I’m putting together the complete design package for an autonomous lawn-mowing robot that can handle more than 1.5 acres of mixed terrain while chiefly trimming short grass. Your task is to turn the core idea into a build-ready set of documents: 3D CAD models, detailed mechanical drawings, motor and drivetrain selection, control architecture, and a clear wiring diagram. Because the property combines flat stretches with gentle hills, stability and traction strategies—such as an articulated or independently driven wheel setup—need to be baked into the concept. I also want straightforward, sensor-based navigation (GPS + RTK or comparable) and obstacle detection that can be sourced with readily available components. Key deliverables • Native CAD files (SolidWorks...

1) Project goal Design a single PCB device for testing cable harnesses up to 25 wires, where both ends of the same harness are connected to the board: Side A: 25 lines (A1..A25) Side B: 25 lines (B1..B25) Total: 50 signal lines on the PCB. The detailed test logic (continuity/shorts/mapping) will be implemented in firmware later. For this phase, the key deliverable is robust hardware (schematic + PCB) prepared for such testing. 2) Scope of work (hardware only) Electrical schematic PCB layout Production files: Gerbers + drill BOM (with specs and acceptable alternatives) Assembly files (pick&place/positions) preferred Short mapping table: MCP23017 pins → A/B line numbers (Firmware is NOT required in this phase. Optional “I2C scan / basic blink” is a bonus.) 3...

I am midway through an online electrical training program and still have two graded components left in each module: the “learning activity” and the “content quiz.” Both are multiple-choice, can be retaken without limit, and I need a final score of 90 % or higher on every attempt that counts toward my record. You will receive screen-shots of every unfinished unit plus login access so you can work directly in the platform. Feel free to lean on AI tools or any personal reference material; the school places no restriction on outside resources. When you reply, please mention any hands-on electrical background, coursework, or certifications that show you can navigate these topics confidently. Deliverables • All remaining learning activities submitted with ≥...

I’m looking for an experienced electronics designer to develop a complete industrial-grade control system consisting of two devices: 1. Transmitter (TX) – collects inputs from joysticks and other signals (8 analog + 2 digital + AUX). 2. Receiver (RX) – receives data from TX via CAN and drives power outputs. Communication between TX and RX must be via CAN bus. The system must operate on 12V or 24V vehicle/machine installations, with a supply range of 9–27V DC. Scope includes schematic design, SMD PCB design, and enclosure selection/design. ⸻ Functional Requirements TX (Transmitter) • 8 analog input channels (joysticks / analog signals) • 2 digital inputs • 1 AUX signal (logic/auxiliary) • Analog measurement must use an industrial-grade ...

I need a purpose-built Wi-Fi modem that can sit in the field, discover and manage between twenty and thirty of my smart prepaid electric meters at once, then forward their information to a third-party server. Core requirements • Meter side: maintain a stable local link to each prepaid electric meter, poll at configurable intervals, queue data when the Wi-Fi link is down, and reconcile immediately after reconnection. • Network side: connect via standard 2.4 GHz Wi-Fi, authenticate securely (WPA2 minimum), and push three distinct data streams—usage statistics, diagnostics snapshots and real-time alerts—through the API endpoints I will supply. • Throughput: normal operating load is small, but latency for real-time alerts must stay below two seconds under fu...

Seeking experienced hardware engineer to build a prototype of a wall-mounted emergency device. Specs: Form Factor: Wall-mounted, compact, durable enclosure (weatherproof if outdoor use intended). Primary Function: Transmit pre-programmed GPS coordinates to a central monitoring location (e.g., server, app, or emergency service) upon activation for real-time tracking. Transmission Methods: Primary: GSM (cellular network) for cost-effective, low-latency sending. Failover: Satellite (e.g., Iridium or Globalstar network) if GSM unavailable. Power Source: Battery-powered with optional mini solar panel for recharging. Standby Battery Life: Minimum 1 year without charging (low-power mode). User Interface: Single button for activation; 2 LEDs for status feedback. Key Features Programming: Devic...

My 4.5 V circuit needs a small solar panel and the proper charge-management hardware so daylight tops the battery up automatically. I’m not sure what panel voltage or wattage is best, nor which controller IC will keep the Li-ion safe—so I need your electronics expertise. Scope of work – I'll share my schematic of the existing 4.5v circuit – Select or design a charge-controller stage that handles lithium-ion chemistry, prevents over-charge/over-discharge, and outputs a stable 4.5 V rail to the load. – Provide a clear schematic, concise BOM with part numbers that are easy to source, and wiring instructions I can follow on perfboard or a small PCB. – Advise on any protection components (diodes, fuses, reverse-polarity safeguards) so the device...

Project Description: I'm building a compact, consumer-grade handheld device that hosts multiple ARM processors and modules on a single 4-layer board. The design must accommodate a high-speed USB hub, balanced power distribution, and impeccable signal integrity without exceeding the layer budget. Components to Integrate: Component Details Interface Luckfox Lyra Zero W ARM Cortex-A7 Linux SBC (65×30mm, 40-pin header) Direct solder or socket Teensy 4.1 ARM Cortex-M7 @600MHz audio DSP (61×18mm) 2.54mm headers SL2.1A USB Hub IC 4-port USB 2.0 hub Surface mount XIAO ESP32S3 LoRa module (21×18mm) 1.27mm headers STM32WB55 Module Dual-core ARM Cortex-M4/M0+ (Flipper brain) 8-pin header PyBoard v1.1 ARM Cortex-M4 backup controller 6-pin header GPS Module NEO-6M/8M 4-pin heade...

I need an experienced electronics / PCB engineer to design a reliable 24/7 traffic light controller PCB. This is a safety-critical industrial system, not a hobby project. System Details: 220VAC traffic light LED modules Control via TRIAC (optocoupler + TRIAC driver) Continuous 24/7 operation ESP32-based control Fail-safe design required Industrial-grade AC mains design Using EasyEDA Requirements: Strong ESP32 hardware experience Experience with AC mains / TRIAC design Experience with industrial / high-reliability systems Comfortable designing fail-safe protection systems Timeline (strict): Day 1: Complete schematic Day 2: PCB placement & routing If it takes longer, it means you are not experienced enough — this is not a complicated project. You must be ready to...

I need the 2026 GC front panel converted into a production-ready Gerber package so my board house can mill an exact aluminum faceplate. All mechanical data are already prepared: you’ll receive a clear photo of the current panel plus an Excel sheet detailing every cut-out, hole diameter, and positional coordinate. No circuitry is involved—this is purely a mechanical PCB. Here’s what I expect: • A clean RS-274X Gerber set, including drill file, that matches the spreadsheet dimensions to the tenth of a millimetre. • A simple PDF drawing or fabrication note that calls out all critical sizes for one last visual check before I release it to the shop. Please stick to the manufacturer’s standard rules; I’ll share their design-rule file once we start, ...

I need a medium complexity (3-4 layers) PCB designed for signal processing. The design should be capable of accommodating surface-mount components. Requirements: - 3-4 layers PCB design - Signal processing functionality - Surface-mount component integration - Gerber file generation Ideal Skills: - Experience with PCB design software (e.g., Altium, Eagle) - Strong understanding of signal processing circuits - Proficiency in layout for surface-mount components - Attention to detail and accuracy Please provide samples of previous work.

I have a finished KiCad PCB layout and now need a clean, print-ready PDF compiled from it. The final document must contain six A4 landscape pages arranged in this exact order: 1. Copper Top Layer 2. Copper Inner Layer 1 3. Copper Inner Layer 2 4. Copper Bottom Layer 5. Component Placement Top Layer 6. Component Placement Bottom Layer Resolution has to be crisp enough for both close-up review and high-quality printing. I’ll provide the KiCad source files as soon as we get started; you simply export each required layer, keep KiCad’s default rendering colours, and merge them into a single PDF. I’ve attached a previous example—please note the labels are mirrored on that file due to an earlier issue, so yours should read correctly. Deliverable • O...

Hello, I am looking for an experienced PCB designer to complete schematic review and PCB layout for an ESP32-based industrial IoT board using EasyEDA (Collaborator mode). Scope of Work 1. PCB Outline & Mechanical Alignment The PCB outline must match an existing device layout based on measurements and connector positions that I will provide. There is no reference Gerber file, so the board outline must be recreated carefully and confirmed with me before routing. 2. Schematic Review & Improvement (Important) You must review the schematic and confirm it is electrically correct and suitable for stable operation, including: Component ratings verification Power design validation Decoupling and grounding ESP32 stability considerations LM2596 switching regulator layout considerations Identi...

I'm seeking an experienced PCB designer to create a double-layer PCB for a consumer electronics radio project. The PCB will include microcontrollers as key components. Key Requirements: - Design a double-layer PCB - Incorporate microcontrollers into the design - Suitable for consumer electronics use Ideal Skills and Experience: - Proficiency in PCB design software (e.g., Altium, KiCad) - Experience with double-layer PCB design - Knowledge of microcontroller integration - Background in consumer electronics Please provide samples of previous work and relevant experience.

I need an existing wiring schematic revised to add one component. Requirements: - Current schematic is scanned from PDF - Need to add a green pilot light Ideal Skills: - Experience with wiring schematics - Proficient with PDF editing and schematic modification - Attention to detail and accuracy

Custom TWS Earbuds Prototype - Earin M-2 Miniaturization** UNIVERSITY PROJECT: Redesign Earin M-2 earbuds SMALLER to reduce ear protrusion. CURRENT SPECS: 24×15×15mm shell, 4g each, 60mAh battery, 4hr playback, BA driver, NFMI sync, touch controls TARGET SPECS: <20×13×12mm shell (33% smaller volume) • Same features or close equivalents • 1-2 FULLY WORKING prototype pairs DELIVERABLES REQUIRED: 1. New shell design (3D printed or molded) 2. Custom PCB layout for reduced volume 3. Component sourcing (mini BA driver, BT/NFMI, 40-50mAh battery) 4. Full assembly + functional testing 5. Audio test + TWS pairing validation I HAVE: • Complete Earin M-2 teardown photos • Exact measurements + target dimensions • Protrusion problem photos &bu...

I am developing a compact handheld consumer device prototype that requires integration of a rechargeable battery and small electronic module inside a custom 3D printed enclosure. I am looking for an experienced embedded hardware / electronics engineer who can help design and prototype a small, safe, battery-powered system suitable for a handheld form factor. The device will require: • Integration of a rechargeable lithium battery (3.7V or similar) • Safe charging system (USB-C or similar) • Small heating or vapor-generating element OR similar compact load component • Efficient power management and protection circuitry • Compact PCB design suitable for fitting inside a slim enclosure • Guidance on component selection and prototype assembly The enclosur...

Projeto: Engenharia Reversa de Placa Eletrônica Legada Descrição do Projeto Busco profissional com experiência comprovada em eletrônica para realizar engenharia reversa completa de uma placa eletrônica legada, com o objetivo de: Reproduzir fielmente o funcionamento elétrico original Modernizar componentes obsoletos Gerar documentação técnica completa e atualizada Garantir compatibilidade mecânica, elétrica e funcional com o equipamento original O projeto seguirá um procedimento técnico estruturado já definido internamente Escopo do Trabalho O profissional deverá executar as seguintes etapas: 1. Análise e Correlação do Esquemático Verificaç&...

I new to design a PCB dedicated to processing several signals and starting a device based on a set number of conditions. I would like to be able to modify those parameters from a cloud based or simple web interface. The board should handles both analog and digital. I expect all to be digital signals but just in case. It should basically handle, temperature, humidity and time of day. Deliverables 1. Compiled firmware binaries plus full, buildable project files 2. Clear inline comments and a concise README explaining build steps and pin mappings 3. A short test report that documents signal-integrity measurements and confirms the module meets the agreed specs. 4, Plus device recommendation and also help on setting up. I have an idea, but I am a genetic engineer. I am OK with basi...

I already have the full schematic and the finished PCB files for a board that combines an ESP module with a PIC18F microcontroller. What I’m missing is a clear, practical explanation of how everything talks to each other, especially over UART, and how that interaction is implemented on the physical board. Here is what I need from you: • A step-by-step walkthrough of the signal paths that handle UART traffic between the ESP and the PIC18F, including any level-shifting, buffering, or hand-shake lines that support the link. • A guided tour of the PCB layout that shows where those signals travel—layer changes, vias, ground references, decoupling, and any routing choices that affect integrity or noise. • Simple notes on any supporting circuitry (power rails, ...

I've already built some prototypes of a circuit capable of switching a single 230 V, 16–30 A line to 4, 8, or 12 outputs—without power loss—but none of them have reached the standards I expect. I have schematics, calculations, thermal measurements, and test logs: enough material to clarify every technical detail and speed up your work. I need a senior designer who can transform all this into a final solution, complete with ESP32 firmware, a multilayer PCB (4 or 6 layers, JLCPCB production - 3oz copper), and an accurate and documented simulation before production. Technical requirements to be met: • Maximum energy efficiency, component protection, and precision switching under load. • Integrated remote control, real-time monitoring, and an alarm system. &b...

I already have the full schematic and the finished PCB files for a board that combines an ESP module with a PIC18F microcontroller. What I’m missing is a clear, practical explanation of how everything talks to each other, especially over UART, and how that interaction is implemented on the physical board. Here is what I need from you: • A step-by-step walkthrough of the signal paths that handle UART traffic between the ESP and the PIC18F, including any level-shifting, buffering, or hand-shake lines that support the link. • A guided tour of the PCB layout that shows where those signals travel—layer changes, vias, ground references, decoupling, and any routing choices that affect integrity or noise. • Simple notes on any supporting circuitry (power rails, ...

Ho già costruito alcuni prototipi di un circuito in grado di commutare un’unica linea da 230 V, 16–30 A, verso 4, 8 o 12 uscite; --senza perdita di potenza--, nessuno, però, raggiunge ancora gli standard che mi aspetto. Dispongo di schemi, calcoli, misurazioni termiche e log di prova: materiale sufficiente per chiarire ogni dettaglio tecnico e velocizzare il tuo lavoro. Mi occorre un progettista senior che sappia trasformare tutto questo in una soluzione definitiva, completa di firmware su ESP32, con PCB multilayer (4 o 6 strati, produzione JLCPCB - copper 3once) e una simulazione accurata e documentata prima della produzione. Requisiti tecnici da rispettare • Massima efficienza energetica, protezione dei componenti e precisione nella commutazione sot...

I’m replacing my existing pool circulation unit with a single-speed pump that I already have on site, along with all the fittings, unions, and electrical hardware required. The pad is clear, the plumbing is exposed, and access from the driveway to the equipment area is wide open, so getting tools and materials in place will be straightforward. What I need is a qualified installer who can: • Plumb the new pump into the current PVC line, ensuring airtight, leak-free unions • Make the electrical connection to the existing breaker, verify correct voltage, and bond/ground to code • Prime, test-run, and fine-tune the flow so the system reaches full pressure without cavitation • Leave the pad clean and walk me through basic operation once everything is running sm...

I need a detailed wiring diagram to support a building permit application for a five electrical panel system at an apartment building in Huntington Beach, California. Requirements: - Must be a wiring diagram - Includes main electrical feed into the apartment and 5 separate electrical panels - Must include panel numbers and locations Ideal skills and experience: - Expertise in creating electrical wiring diagrams - Knowledge of building permit requirements in California - Experience with multi-panel electrical systems Please provide a sample of similar work done.

Hello , I have a cabled weather station ready to go, but I need an experienced hand with the physical installation side only. The job covers everything from mounting the sensors and console, running and securing the cable, to making sure connections are weather-proofed, grounded, and reading correctly once powered up. Brand is flexible—I simply need someone familiar with the usual hardware found in systems such as Davis Instruments, AcuRite, La Crosse, or similar. Only serious freelancer Auto bids not good Thank you

I’m developing a compact medical-grade board that will sit at the heart of a new vital-signs monitor. The PCB must reliably acquire and process heart rate, blood pressure, and respiratory rate signals, then pass the data to a microcontroller for further analysis and display. Here’s what I need from you: • Complete schematic capture based on my sensor and MCU selections • Four-layer board layout optimized for low-noise biomedical signals (Altium or KiCad preferred) • Manufacture-ready Gerber files, pick-and-place data, and a clearly structured BOM with medical-grade component choices • Design reviews at schematic and pre-release layout stages so we can make sure the board meets IEC 60601-1/-2 spacing, leakage, and isolation requirements • Brief ...

I need a PCB designed specifically for a one-off project; it is not part of a commercial product line, so flexibility and creativity are welcome. The board will carry only analog circuitry—no digital sections—centred around operational amplifiers and a small signal-processing stage I will detail once we start. What I will supply: the schematic (PDF or KiCad), preferred footprints, and basic mechanical constraints. What I need from you: a clean, manufacturable layout with proper analog grounding practices, complete Gerber/ODB++ files, a reviewed BOM, and the original design file so I can revise it later if needed. Please aim for standard two-layer construction unless you advise otherwise for noise reasons. Acceptance will be based on: • DRC-clean files that import i...

The task is to design a compact PCB that drops straight into an SCX 1/32 car so it can run on a digital track. I want the board to read the track’s reed-sensor signal, let me assign any of 20 unique car IDs in firmware, and expose a surface-mount USB-C port on the edge for easy flashing once the body shell is back on. Size must stay close to the original analogue board footprint (about 24 × 18 mm, height under 6 mm) but I can adapt mounting holes or connector positions if you have a cleaner layout idea. Power comes from the standard track pickups (nominal 14–18 V DC), so include an efficient buck or LDO to feed the microcontroller and reed circuitry. I haven’t locked the MCU yet; pick anything small, inexpensive, and easy to program—ATmega, STM32, ESP32, or s...

I’ve drafted a single-layer board in Altium Designer and now need a seasoned set of eyes to run thorough simulations before I commit to building the first prototype. Your task is to import my project, verify the stack-up and component models, and perform all relevant electrical, thermal, and rule-check simulations available in Altium. Key goals • Confirm that signal integrity and power distribution meet design intent. • Flag any DRC or manufacturing issues early so I can correct them before fabrication. • Produce a concise simulation report summarizing the tests run, key plots or screenshots, and your recommendations. Deliverables 1. Updated Altium project files with all simulation settings preserved. 2. PDF or DOC report of findings and suggested fixes. ...

I need a clean, well-structured Process Flow Diagram for an Oil and Gas Manufacturing Company that will be used primarily as a training and instruction aid for operators and new hires. I already have the P&ID sets that will be used as the basis in digital form, so you can start by refining and reorganising that file rather than drawing every symbol from scratch. The job is straightforward: translate the existing digital schematics into a single, professional-grade PFD with clear tagging, line weights, and legend so it is easy for a trainee to follow. Consistency of instrument symbols, line numbering, and valve identification is critical because this graphic will be embedded directly into our training manuals. Please work in any mainstream CAD platform you are comfortable with&mdash...

I need a detailed electrical plan for installing an EV charger in the garage of a new residential home, as required by council regulations. The home has a three-phase electrical supply. Requirements: - Compliance with Woollahra council regulations For condition 14 (Item 37) that requests “electrical plans of all off street parking demonstrating capacity for Level 2 (single phase, 7kw power) charging point” - Detailed schematics for three-phase supply - Specifications for EV charger installation in garage Ideal Skills and Experience: - Experience with residential electrical planning - Knowledge of council requirements for EV charger installations - Familiarity with three-phase electrical systems

I need a compact, production-ready circuit that brings reliable wireless communication to a new consumer-electronics device. The work begins with schematic capture and component selection, moves through PCB layout, and finishes with ready-to-manufacture Gerbers, a complete BOM, and clear test guidelines. The radio link is the heart of the design, so careful RF layout, antenna matching, and regulatory-compliant power levels are essential. Bluetooth LE is my preferred protocol, though I am open to Wi-Fi or other 2.4 GHz solutions if you can demonstrate lower cost or better battery life without sacrificing performance. Please plan on: • Delivering editable design files in Altium, KiCad, or Eagle, plus PDFs for quick review • Calling out any critical components with long le...

I need a Zigbee Green Power device for indoor lighting control. The primary features required are on/off switching and dimming. Key requirements: - Zigbee Green Power technology - Indoor installation - On/off switching and dimming capabilities Ideal skills and experience: - Familiarity with Zigbee technology - Experience in lighting control systems - Electrical installation knowledge for indoor environments

Kérjük, regisztráljon vagy jelentkezzen be a részletek megtekintéséhez!

I want to build a compact, two-way Bluetooth audio interface for a HAM radio. The core goal is a 2-way bridge between the radio and a realtime camera running on a linux board via buletooth. Digital or analog volume adjustment is needed Device must be battery and/or 12V DC operated, with DC12V charging battery if present What I need: • Full-duplex transmit and receive so both the radio’s microphone and speaker lines travel over Bluetooth. • A design that plays nicely with typical HAM radio mic/headphone levels. • Optional Radio PTT Sense to mute microphone input if PTT button not pressed • Stable pairing, clear voice quality, and minimal latency. Please provide: 1. Schematic and bill of materials (module choice is up to you; CSR, ESP32, or similar is fine). 2...

I want to create a clean, minimalist cyberdeck housed entirely in plastic that integrates a single key component—a keyboard. No display, no battery pack, just a compact typing-focused deck that feels modern and clutter-free. What matters most is the look and ergonomics. The enclosure should have smooth lines, a slim profile and zero ornamental extras; think understated rather than steampunk or gamer aesthetic. Plastic choice, wall thickness, and internal standoffs must support daily use without flexing. If you have experience with 3D-printed ABS/PLA shells or injection-moulded designs, great—either method works as long as the finished chassis is durable and easy to replicate. Internally, please leave enough space and mounting points for a standard USB or hot-swappable mechani...

I already have a working ESP32 design in KiCad and need it brought to its final, production-ready form for a commercial product that must clear CE. The job centres on three key changes: swapping the Micro-USB for a USB-C connector, integrating a Li-Po charging IC, and tweaking the board outline and component placement so everything fits a new enclosure while preserving optimal antenna clearance, decoupling, and thermal performance. Please keep manufacturing constraints in mind and pass every KiCad DRC before delivery. Timeline is tight three days from award so I’m looking for someone who can move quickly yet meticulously. Deliverables • Updated KiCad project (schematic and PCB) • Fabrication package: Gerbers, drill files, BOM, and pick-and-place (CPL) ready for PCB...

I am looking for an experienced RF hardware designer to consolidate and miniaturize an existing RF system based on a MYIR Zynq-7020 board. The current setup includes: 1. MYIR Zynq-7020 board (fixed, no redesign) 2. Adapter board 3. Two separate RF transmitter boards The goal is to integrate the two RF boards and the Adapter board into a single compact adapter board, while keeping the existing electrical interfaces to the MYIR board unchanged and minimizing or avoiding FPGA/firmware changes as much as possible. Scope of Work (High Level) - Integrate two RF transmit chains on one board - Use a shared reference oscillator and PLL for both RF paths - Replace discrete RF filters with compact off-the-shelf RF filters - Replace legacy power regulators with modern, small LDOs - Add RF routing op...

I’m building a mini ventilator—an embedded medical device combining mechanical and electrical subsystems—and I’m looking for a dependable partner who can translate detailed specifications into working hardware and firmware. Your responsibilities will include hardware design, firmware development, and end-to-end integration and testing. How we’ll work: • I’ll provide clear, itemized requirements; you’ll convert them into schematics, PCB layouts, and clean, well-documented firmware. • We’ll maintain a tight feedback loop with regular progress updates, clarification where needed, and rapid iterations after reviews. • Accuracy, reliability, timelines, and strict confidentiality are non-negotiable. Expected deliverables (as appli...

You will be living and have the right to work in the UK. We need a skilled electrician to upgrade and complete several control panels across multiple sites in London and Southampton so you will be mobile and have your own tool kit. Key tasks include: - Finish wiring control panels to 3-phase pumps - Wire control panels from scratch - Swap out a PLC on-site in Southampton, converting inputs from 0 to 24V - Full testing and commissioning after wiring Ideal skills and experience: - Electrical engineering background - Experience with 3-phase systems and PLCs - Ability to upgrade and wire control panels - Proficient in testing and commissioning electrical systems Please provide relevant experience and a timeline for completion.

I’m a 20-year-old from Nepal putting together a small handmade craft project and would love a creative partner to help me bring the idea to life. The vision is clear in my head, but I need professional input to refine the design, choose materials that are easy to source locally, and map out each construction step so I can reproduce the final pieces on my own. Here’s what I’m hoping you can do: • Develop two or three polished design options, each with notes on colours, textures, and any special finishes. • Create simple diagrams or digital mock-ups that walk me through every assembly stage. • Provide a concise materials and tools checklist that matches what’s commonly available here in Nepal. Acceptance criteria: designs and diagrams delivered ...

I’m putting together a compact desk ornament that spins on command, and I need a complete PCB solution to drive the rotation reliably. The ornament will only move when a small switch is flipped—no sensors, no remotes, just simple manual control feeding a quiet motor. Main Features: • main power source is 5V from USB to DC power jack connected to board via JST-PH cable 2pin socket. • 3.7V 800mAH Lithium chargeable battery as backup power source, connected via JST-XH cable. • 3-way SPDT switch(on, off, timer) connected to the PCB via a JST-XH cable. • 3V DC motor with peak current around 3A, connected to board via JST-PH(2pin) • 2 mounting points (M3 size to allow M2.5 bolts) Here’s what I’m after: • Schematic and PCB layout for a ...

PCB Technical Blog Writing Guidelines Each week I publish in-depth, EEAT-driven articles that demystify printed-circuit-board design and manufacturing for an audience of intermediate professionals. The primary goal is to educate—every post must read like it was penned by someone who has actually laid out boards, debugged traces, and wrestled with impedance calculations, not by a generic content mill. Scope of work You will draft original how-to guides that walk readers through real engineering challenges (e.g., stack-up selection, thermal relief strategies, DDR routing tips). Practical detail and accurate terminology are essential; surface-level summaries or re-hashed competitor pieces won’t be accepted. Quality standards • EEAT: demonstrate personal experience,...