Arduino Stepper Motor Dc Motor control

Arduino skech(firmware) needed with pinouts and explanations.

I have those parts.

-Arduino Uno or Mega

-Easydriver(stepper motor driver)([url removed, login to view])

-L298N(double dc motor driver)([url removed, login to view])

-2 pieces limit switches..Switch1 and Switch2 (optical switch/photo interrupter/[url removed, login to view])

-1 piece dc motor 12volt (works as a slider between Switch1 and Switch2 /dc motor works with L298N)

-1 piece rc servo motor (it will push and pull an arm/ works with Arduino Uno)

-1 piece nema17 stepper motor 200steps 1.8Degree 12volt(works as a turn table)

-1 piece 12 volt buzzer(works with L298N)

-1 piece sensorXXX for Stepper motor /Home position

-1 piece Push Button

-1 piece Green led


Stepper Motor: There is a turntable that has 10 [url removed, login to view] turntable is attached to stepper motor.

it will turn 36 degrees per movement(so total there will be 10 movements).Each Turntable turn 36 degrees Rc servo Motor

will put somethingXXX into turntable each groove.

Also Dc Motor is putting somethingXXX into turntable each groove.


system power on;



1-Dc Motor will goto switch1 and waits..if it is already in Switch1 same it will waits.

2-Rc servo Motor turns 80 Degrees CW..and waits.

3-Stepper motor will go to 1st groove on Turntable with a help of sensorXXX which is attached to the turntable.

4-Calibration finished and Green Led activated.

***All above steps must be in order.


When green led is active,user will Push the button..and system starts.


1-Rc Servo turns 40 degrees CCW.

2-Dc Motor will go to switch2 at same time buzzer will work.

3-When Dc motor reaches switch2,

a-Buzzer stops

b-rc servo turns 80 Degrees CW,

c-Dc motor reverse and go to Switch1.

***(a,b,c steps must be in order)

4-When Dc motor reaches switch1 wait for stepper movement, now stepper motor turns 36 [url removed, login to view] turntable 2nd groove is


5-When 2nd groove is [url removed, login to view] to step1 and so on...

***these all steps must be in order.

*** when stepper is turning..dc motor must be at switch1 and servo motor will be at 80 [url removed, login to view] there will be crash.


Készségek: Arduino, C programozás, C++ Programozás

Bővebben: control motor with arduino, arduino control motor via wifi, arduino stepper motor wiring, arduino stepper motor circuit, circuit arduino stepper motor circuit, arduino stepper motor sketch, arduino stepper motor control code, arduino stepper motor project, arduino stepper control, arduino stepper motor control sketch, arduino stepper motor control joystick, arduino stepper motor cnc program code, arduino stepper shutter control, control motor stepper labview, control motor potentiometer

A munkaadóról:
( 1 értékelés ) ankara, Turkey

Projektazonosító: #12208671



Hello my name is Manuel I'm Mechatronic Engineer I have experience working with Arduino in projects, I have worked with DC Motor, Servo, stepper and other elements (Shields, LCD, sensors, etc..) I would like develop yo Több

$35 USD 4 napon belül
(37 értékelés)

11 szabadúszó tett átlagosan $354 árajánlatot erre a munkára


Hello, I am an Electronics and Embedded system developer. I have experience in Digital and Analog electronic design and Matlab. I well versed in Arduino hardware and software. Kindly check my profile. Reply me back and Több

$1200 USD 15 napon belül
(25 vélemény)
$140 USD 5 napon belül
(45 vélemény)

Hello Client I have seen ur project details and i believe that i can do ur task efficiently and within time span u r providing i am electronic engineer, kindly review my profile and then decide My projects (major Több

$45 USD 2 napon belül
(22 vélemény)

Hi... I have 6+ years of experience in the field of electronics and communication. I am working on different industrial based project where my primary role was to design embedded system, programming of micro-controller Több

$50 USD 10 napon belül
(13 vélemény)

I am an Electrical Engineer having specialization in Electronics and Control, teaching in Electrical Department at FAST National University Pakistan. I am also persuing my MS degree in Electrical Engineering with speci Több

$200 USD 3 napon belül
(9 vélemény)

Hello! I can carry out your project. I have all the necessary equipment (microcontrollers and modules) in my studio. I've had experience in writing firmware for such devices. But In fact, I need a more detailed desc Több

$100 USD 15 napon belül
(11 vélemény)

Hi, I am a Design engineer, recently graduated from IIT Madras in Engineering Design ( specialized in both Mechanical and Electrical Engineering) and currently working in sustainability-related start-up called Enfrien Több

$40 USD 10 napon belül
(1 Visszajelzés)

Hello, I'm very much interested in your project because I already worked in compatible motor controller + driver for L298 using L297. I can give you datasheet and pin out diagrams with clear explanations with sample c Több

$40 USD 10 napon belül
(0 vélemény)

Hi, I am a mechanical & product engineer with a dedicated team of inhouse mechanical, electronics hardware and software engineers. We have published 9 international papers and 5 patents. In past we have designed com Több

$2000 USD 30 napon belül
(0 vélemény)

Merhaba, Projenizi okudum, istediğiniz sistemi Arduino ile inşa edebilirim, kodunu açıklamalarıyla size gönderebilirim. ODTÜ, Havacılık ve Uzay Yük. müh liği mezunuyum. 5 yıllık tasarım ve üretim konusunda tecrübem Több

$45 USD 10 napon belül
(0 vélemény)