Find Jobs
Hire Freelancers

Firmware needed for STM32F4 Discovery evaluation board

$30-250 USD

Folyamatban
Kiadva ekkor: majdnem 6 évvel ezelőtt

$30-250 USD

Teljesítéskor fizetve
I need programmer to help me finish up an application for a STM32F4 Discovery. The application must read samples from the onboard MEMS microphone and run FFT. It will then report the frequency,magnitude values over USB. The existing code has USB running as custom HID and the actual microphone sample acquisition and transmission must be implemented. Existing code uses gcc and STM Cube HAL drivers and such it would be great to continue with these tools. Need source code and build binary file.
Projektazonosító: 17024259

A projektről

8 ajánlat
Távolról teljesíthető projekt
Aktiválva: 6 évvel ezelőtt

Szeretne pénzt keresni?

A Freelancer oldalán történő árajánlatadás előnyei

Határozzon meg költségvetést és időkeretet
Kapja meg fizetését a munkáért
Vázolja ajánlatát
Ingyen regisztrálhat és adhat árajánlatot munkákra
8 szabadúszó adott átlagosan $344 USD összegű árajánlatot erre a munkára
Felhasználó avatár
I am very experienced in development on ARM-based boards including the STM32 and NXP families of microcontrollers. I work with STM CUBE HAL Libraries. I also have experience compiling with GCC and Keil IDE. Please contact me with more details of your project.
$333 USD 3 napon belül
4,8 (50 értékelés)
6,3
6,3
Felhasználó avatár
Dear Sir, I am an expert in STM32F4 with more than 15 years of experience in the field of embedded systems, electronics, prototyping and PCB Layout. I have worked with GCC tools using HAL cube libraries. I also have the STM32F4 Discovery board here Regards Ch
$150 USD 3 napon belül
4,5 (71 értékelés)
6,4
6,4
Felhasználó avatár
Dear Sir, I have experience in developing the application based on the STM controller. I have also worked on the USB driver in STM board. Let us discuss the project.
$250 USD 7 napon belül
4,9 (5 értékelés)
4,7
4,7
Felhasználó avatár
A proposal has not yet been provided
$277 USD 3 napon belül
4,7 (15 értékelés)
3,9
3,9
Felhasználó avatár
Hello , I have bachelor's degree in computer science and i have been programming in C/C++ for both linux and windows for more than 8 years.I have written various network applications some of which are down to the IP packet level. Additionally I have extensive knowledge in Intel and ARM assembly and previous experience in reverse engineering and device drivers development for both Linux and Windows. let me know if you're interested
$666 USD 10 napon belül
4,9 (6 értékelés)
3,8
3,8
Felhasználó avatár
Hello there, The project title “Firmware needed for STM32F4 Discovery evaluation board“ has precisely match to our experience in embedded technology. Since last 6+ years, we have been working in technology embedded system. We do have an in-house team who are experienced in all aspect of an embedded system. (Including hardware and software design). One of our huge IOT product is running on "AMUL Dairy" Industry. Here is our core competency. Specifications Design Schematic Design PCB Layout Developed Prototype Test Prototype Firmware Development Test Firmware Certification Have worked on: Data Acquisition system Web server based monitoring system E-commerce application IoT (Internet of Things) We have developed several products using with this communication protocol (SPI, I2C, RS485, RS232, Ethernet 10/100Mbps, USB, Wi-Fi, Bluetooth, Zigbee, GSM/GPRS (Telit, Simcom)) We are keen to discuss further with you about how we can contribute to your company. Thank you Ritesh Prompt Softech
$200 USD 3 napon belül
3,2 (1 értékelés)
3,1
3,1
Felhasználó avatár
I'm an electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (STM32Fx, NXP, EFM32 SiLabs, but I'm ready to learn new frameworks). I work both single task and multi task environment (FreeRTOS and RTX). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management and for high level/final application. I work also in "C code" commercial boards Arduino/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in C, C++, .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too. I have experience in openCV library for image/video processing.
$722 USD 30 napon belül
0,0 (0 értékelés)
0,0
0,0

Az ügyfélről

JAPAN zászlója
Yokohama, Japan
5,0
2
Fizetési mód hitelesítve
Tagság kezdete: júl. 25, 2013

Ügyfél-hitelesítés

Köszönjük! E-mailben elküldtük a linket, melyen átveheti ajándék egyenlegét.
E-mailje elküldése során valami hiba történt. Kérjük, próbálja újra.
Regisztrált Felhasználók Összes Közzétett Munka
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Előnézet betöltése
Hozzáférést adott a helymeghatározáshoz.
Belépési munkamenete lejárt, és kijelentkeztettük. Kérjük, lépjen be újra.