Find Jobs
Hire Freelancers

Design schematic and PCB layout - RK3399 -- 3

$250-750 USD

Lezárt
Kiadva ekkor: több mint 3 évvel ezelőtt

$250-750 USD

Teljesítéskor fizetve
- Reposting - Need an Engineer to design the circuit schematic and PCB layout for a Rockchip RK3399 SoC. This board will use a Linux based OS. All components used (wifi/bt /ethernet controller...) must have working linux drivers. Board will need to have: RK3399 SoC 4GB RAM - LPDDR4 SD Card Ethernet Port - 100M or 1G, depending on component cost. WiFi + Bluetooth - WiFi @ 2.4GHz and Bluetooth at rev 4.0 2 x USB 3.0 - for peripherals 2 x USB 2.0 - for peripherals 18 GPIO buttons LCD connector. Best if RGB24, if can’t be used then MIPI DSI HDMI Port USB Type C Port – For power (and data if enough host) eMMC – 128GB NGFF M.2 SSD connector 4 ADC channels. 6 bit low resolution is OK. It's for joystick components. As many available GPIO as possible. Board dimensions, buttons position, screw holes position, restrict areas and connector positions will be given and must follow precisely the reference, as the PCB will be use as replacement in an existing product. Best to keep same connector models, if connectors are different than the one in reference, then they must be positionned precisely such that they will fit in our product. Please keep PCB layers to a minimum as to keep cost down. Engineer will choose the components and provide a BOM. Engineer has to provide impedance control guidelines. Engineer has to debug the board and make sure it works correctly and is responsible to correct any hardware mistakes or issues. Design must be done using : Kicad or Eagle. Preferably someone who has already done RK3399 layout. At least another ARM board design with another SoC.
Projektazonosító: 26885230

A projektről

13 ajánlat
Távolról teljesíthető projekt
Aktiválva: 4 évvel ezelőtt

Szeretne pénzt keresni?

A Freelancer oldalán történő árajánlatadás előnyei

Határozzon meg költségvetést és időkeretet
Kapja meg fizetését a munkáért
Vázolja ajánlatát
Ingyen regisztrálhat és adhat árajánlatot munkákra
13 szabadúszó adott átlagosan $1 092 USD összegű árajánlatot erre a munkára
Felhasználó avatár
Hi I am experienced PCB designer with more than 15 years of experience. I have extensive experience with SOC system design. Please get in touch to discuss it further Regards
$2 000 USD 15 napon belül
4,9 (261 értékelés)
8,0
8,0
Felhasználó avatár
Hi sir, First we use Altium Designer and such high speed designs need professional software so Altium or Allegro should fit here better. Open source software are not good for it. Secondly, we use Hyperlynx for simulations. Lets discuss more on it first. Regards, Ahmed
$4 000 USD 90 napon belül
4,9 (48 értékelés)
6,7
6,7
Felhasználó avatár
Best PCB Design Expert at your doorstep! Dear Client, I couldn’t stop myself from bidding after going through the description as they are an exact match with my skillset and experience. I have experience in Designing schematic based PCB design and know all the intricacies required to get the job done with perfection. With more than 5 Years of experience in PCB Design and Circuit Design in Altium, I can ensure you best quality work and before time delivery. Following is a brief list of expertise that I am carrying: 1. IOT products development 2. Microcontrollers based circuit design – STM32, STM8S etc 3. Smart Products like Smart watch - GSM/GPRS/GPS etc 4. Wireless Products - BLE/WiFi- ESP32/ESP8266/NRF24L01 5. Low Power Battery Products design – Rechargeable and Non chargeable 6. Power Electronics – Buck, Boost, Flyback etc 7. RK3399 SoC, RGB24, HDMI Port, GPIO 8. LPDDR4, ARM board Please answer the following questions: 1. What are your future plans with this project? 2. Are there any specific market standards like CISPER you are aiming? 3. What will be ambient temperature of this product? 4. Are there any other specific requirements besides the ones you mentioned Let’s have a quick discussion for 5 mins where I would formulate a plan of action of how we shall take this project to the horizons of success. Regards Pratibha(Nickname -Avi) Quality is never an Accident
$500 USD 2 napon belül
5,0 (12 értékelés)
5,5
5,5
Felhasználó avatár
Hi. I am a PCB designer with rich experience in SBC PCB design. I have read your project very carefully, so I am very confident on your project. I will finish your project in a short time perfectly. Best regards, Andrii.
$700 USD 5 napon belül
5,0 (12 értékelés)
4,8
4,8
Felhasználó avatár
Dear Client. I have just read your job description and your project is really interesting to me. I have many experiences working for 12+ years with Circuit design, PCB design, manufacturing functional prototyping with firmware programming and testing especially. Here are some of the experiences that I built ago. - Schematic and PCB design and Layout using Altium Designer, Eagle. - high-speed, flexible, Multi-Layer PCB design. - DDR, motor control, power converter, POE, UART, SPI, I2C, RF, BLE design - ARM, DSP, MCUs, Arduino, Raspberry pi experiences. I am sure I can complete it on time with high quality. If you hire me, I can start to work for your job immediately. I'll do my best for you. Thank you for your time. Best regards.
$500 USD 3 napon belül
5,0 (11 értékelés)
4,4
4,4
Felhasználó avatár
Dear Client, I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in Designing schematic and PCB layout - RK3399 and could design it for you as per your requirements. I am having more than 15 years of experience in PCB Design, Circuit Design, Circuit simulation, IOT products development and building electronic products. The expertise of mine is in the following fields: 1. Wireless Products – BLE, Wifi, NFC, LoRa etc 2. Power Electronics- Buck, Boost, Flyback, Half Bridge etc 3. IOT sensors interfacing – Pressure, Temperature, Moisture, PH etc. 4. Microcontrollers- ESP32, STM32, STM8S, RL78 etc. 5. GSM, GPS, GPRS 6. RK3399, LPDDR4, GPIO buttons, LCD connector 7. NGFF, SSD connector, Eagle After reading your project details, I have certain queries and suggestions: 1. What is the application of this product? 2. What will be ambient temperature of this product? 3. What are the mechanical constraints to be taken care of? 4. What are the standards that the product would be complying to? 5. What are the user protections required for this project? Please try to answer these questions based on which I would be providing free of cost consultation. I am new to this site but I am an expert in electronics product development. Please message me so that I can formulate a success plan for this project. Waiting for your reply, Regards Hari Mohan Engineering for one is a magic for others
$400 USD 2 napon belül
5,0 (2 értékelés)
4,4
4,4
Felhasználó avatár
Hi, We can surely design the circuit schematic and PCB layout for a Rockchip RK3399 SoC. We can help you in this project as we are an innovative team of Embedded Hardware & Firmware development experts driven by solutions and results. Kindly spare 10 minutes for the interview. We have already developed many electronic products:- GPS Controlled Relay Event status using CC1310 chip Prayer Watch Wireless Alarm System Power Bank Camera slider controller Wifi home automation Bulb with remote control Curtains with remote control Automatic flush control Smart watch for hajj We will be glad to hear from you! Regards, Intellisense Technology
$350 USD 10 napon belül
4,9 (5 értékelés)
4,4
4,4
Felhasználó avatár
hye dear i am electrical enginier and pcb expert i have done many projects about pcb.. check my profile i have vast of knowledge please,.. i give you 100% good result... text me for you project give you good result....
$250 USD 1 napon belül
4,8 (34 értékelés)
4,1
4,1
Felhasználó avatár
Hello. Hope you’re doing well. I am a professional PCB/schematic designer with custom dimensions. Please have a look at my portfolio for few circuit designs. https://www.freelancer.com/u/ayazurrehman Provide quality assurance. Thank You
$500 USD 3 napon belül
0,0 (0 értékelés)
0,0
0,0
Felhasználó avatár
Professional PCB designer in aerospce and defence sector Relevant Skills and Experience 3 years of experience in Pcb layout and schematic input
$389 USD 7 napon belül
0,0 (0 értékelés)
0,0
0,0
Felhasználó avatár
I'm having experience with Embedded Hardware Domain for more than 2 yrs and I'm working with one of the Biggest Electronics and Automation Industry from 1 years. Ihave relevant experience to work with Relevant Skills and Experience I'm having experience with Embedded Hardware Domain for more than 2 yrs and I'm working with one of the Biggest Electronics and Automation Industry from 1 years. Ihave relevant experience to work with
$1 111 USD 10 napon belül
0,0 (0 értékelés)
0,0
0,0

Az ügyfélről

FRANCE zászlója
paris, France
5,0
5
Fizetési mód hitelesítve
Tagság kezdete: szept. 2, 2017

Ügyfél-hitelesítés

Köszönjük! E-mailben elküldtük a linket, melyen átveheti ajándék egyenlegét.
E-mailje elküldése során valami hiba történt. Kérjük, próbálja újra.
Regisztrált Felhasználók Összes Közzétett Munka
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Előnézet betöltése
Hozzáférést adott a helymeghatározáshoz.
Belépési munkamenete lejárt, és kijelentkeztettük. Kérjük, lépjen be újra.